Midnight Woodworking

Woodworking

Tag Archives: church altar

Church Altar and tabernacle stand – day 30 – Delivery day

So I put on a few finishing touches before delivery today. I drilled the base of the tabernacle stand so I could attach the columns from the bottom. I countersunk … Continue reading →

September 28, 2013 · 5 Comments

Church Altar and tabernacle stand – day 29

The wiping poly dries pretty quickly, especially when it was the first coat. I was able to squee an extra brush coat on the two tops last night. This morning, … Continue reading →

September 27, 2013 · Leave a comment

Church Altar and tabernacle stand – day 28

Just a quick post this evening. I sanded down all the surfaces that were urethaned yesterday. They did not need much because not much dust settled on altar parts. The … Continue reading →

September 26, 2013 · Leave a comment

Church Altar and tabernacle stand – day 27

The thing I like the least about a project is the finishing. I decided to go with a wipe-on Polyurethane finish for this project. To create a wipe-on ploy, you … Continue reading →

September 26, 2013 · Leave a comment

Church Altar and tabernacle stand – day 26

I finished the last bit of assembly today. I needed to attach the top plates for the raised panels. I used the drill bit from my Kreg pocket hole jig … Continue reading →

September 25, 2013 · Leave a comment

Church Altar and tabernacle stand – day 25

I usually don’t get much done on a monday, but I took off sick yesterday. I had nothing better to do, so I spent the day in the shop. I … Continue reading →

September 24, 2013 · 4 Comments

Church Altar and tabernacle stand – day 24

Ok, I did work on the columns for a few hours yesterday, but I didn’t feel like posting just this one picture. It took nearly two hours to finish the … Continue reading →

September 22, 2013 · Leave a comment

Church Altar and tabernacle stand – day 23

I like working with walnut. It is probably one of my favorite woods. The grain is tight, It smells good when you cut it, and it is very stable. That … Continue reading →

September 20, 2013 · Leave a comment

Church Altar and tabernacle stand – day 22

I have a bit of a head cold starting and I wasn’t feeling all that energetic last night. I decided to stay away from the bigger power tools if my … Continue reading →

September 19, 2013 · 1 Comment

Church Altar and tabernacle stand – day 21

I had a couple of hours to work last night, so I started out sanding down the wood filler on the columns. That took a while, I had a lot … Continue reading →

September 18, 2013 · 3 Comments

Church Altar and tabernacle stand – day 20

So after trying the first two columns with just a few strips of tape to keep them lined up, I decided to stop being cheap and use a crap load … Continue reading →

September 16, 2013 · Leave a comment

Church Altar and tabernacle stand – day 19

Long day today, but I am starting to make some progress. I started the day sanding down the wood filler that I applied to the tops last night. With the … Continue reading →

September 14, 2013 · 1 Comment

Church Altar and tabernacle stand – day 18

I received my new router table insert plate, that I ordered. Now I have dueling routers. This means that I can set up two bits, that work together, and swap … Continue reading →

September 13, 2013 · 2 Comments

Church Altar and tabernacle stand – day 17

I had a little time, last night. Not enough to run the trim for the altar on the Carvewright (3.5 hours), but enough to cut down and install the trim … Continue reading →

September 12, 2013 · Leave a comment

Church Altar and tabernacle stand – day 16

I have received a few software upgrades for the Carvewright CNC router. I now have the ability to import 2D and 3D images, instead of trying to create them in … Continue reading →

September 11, 2013 · Leave a comment

Church Altar and tabernacle stand – day 15

I decided to start off the day yesterday (afternoon) by mixing up a bit more wood filler. Same recipe as before, stained wood flour and hide glue. I thought I … Continue reading →

September 9, 2013 · Leave a comment

Church Altar and tabernacle stand – day 14

My goal today was to get the bases knocked out. I pulled the clamps from the tabernacle base and planed down the high spots and glue joints. Before I can … Continue reading →

September 7, 2013 · Leave a comment

Church Altar and tabernacle stand – day 13

I was all set to return the Domino to my buddy Dave yesterday when I remembered that I completely forgot to build the lower base for the tabernacle stand. So … Continue reading →

September 6, 2013 · Leave a comment

Church Altar and tabernacle stand – day 12

Today, I want to work on the base for the altar, so to make some room, I finished scraping and sanding the tabernacle top. It turned out nice, but that … Continue reading →

September 5, 2013 · Leave a comment

Church Altar and tabernacle stand – day 11

I pulled the clamps off of the tabernacle stand top today. Learning from the altar top, I only use the router to flush trim the end grain. for some reason … Continue reading →

September 2, 2013 · Leave a comment

Number of visitors

  • 373,162 hits

Follow Blog via Email

Enter your email address to follow this blog and receive notifications of new posts by email.

Join 196 other subscribers

Browse by catagory

Browse my archive