Midnight Woodworking

Woodworking

Tag Archives: Pub chairs

More pub chairs – day 15 complete

Finished the fifth coat of tung oil this morning. The chairs were dry and ready for use by the afternoon. Here are a couple of completed shots.

May 19, 2013 · Leave a comment

More pub chairs – day 14

I am applying the second coat this evening. The chairs have dried from the first coat and there aren’t many dust nibs. The tung oil finish went on pretty smooth. … Continue reading →

May 17, 2013 · Leave a comment

More pub chairs – day 13

I finished up the assembly of the second pub chair of this set last night. I decided to go ahead and apply the first coat of tung oil. I should … Continue reading →

May 17, 2013 · 1 Comment

More pub chairs – day 12

I had some help last night in the shop. Adam came down because I had to make the walnut plugs for the chairs. He likes that job because he gets … Continue reading →

May 16, 2013 · Leave a comment

More pub chairs – day 11

I pulled apart the dry-fit parts and started glueing this chair up today. With everything clamped in place, I drilled the 3/8″ plug hole first, then the pilot hole for the screw … Continue reading →

May 14, 2013 · Leave a comment

More pub chairs – day 10

I started out today by marking and cutting the rest of the pieces I need to get these chairs assembled. The first pieces I did were the 5″ leg spacers. … Continue reading →

May 11, 2013 · Leave a comment

More pub chairs – day 9

With the seats cut out yesterday, I started this evening by finishing them up. I took down any high spots around the edges on the spindle sander. Next, I flipped … Continue reading →

May 10, 2013 · Leave a comment

More pub chairs – day 8

Well, the seats are all glued up. I pulled the clamps and, as I suspected, the cauls were stuck to the seat. Just a quick tap with the hammer and they … Continue reading →

May 9, 2013 · Leave a comment

More pub chairs – day 7

I didn’t get a chance to check on the epoxy yesterday. It seems to have cured pretty well. The tape held the form nicely. So far, the best way that … Continue reading →

May 7, 2013 · Leave a comment

More pub chairs – day 6

I ran out this morning and picked up a new toy. Dewalt’s new 12″ sliding compound miter saw. Now I will be able to cross-cut all my larger lumber. My … Continue reading →

May 5, 2013 · Leave a comment

More pub chairs – day 5

Today I am working on the seats for the chairs. I started by creating a template so the curve of the scoop would be similar from one piece to the … Continue reading →

May 4, 2013 · Leave a comment

More pub chairs – day 4

Busy day yesterday, no time to get into the shop. Tonight, well last night since it is 1:00AM, I trimmed up the edges of all the boards I just laminated … Continue reading →

May 4, 2013 · Leave a comment

More pub chairs – day 4

Another quick post today. I glued up the seat backs and the stretchers before running out of clamps. Then I came back an hour and a half later and pulled … Continue reading →

May 1, 2013 · Leave a comment

More pub chairs – day 3

I only had an hour today to work and only about one yesterday. All I am doing at the moment is glueing so I won’t bore you with too many … Continue reading →

April 30, 2013 · Leave a comment

More pub chairs – day 2

Only a few hours to play today. I pulled a couple of walnut boards off the rack for resawing. I need all of the walnut to be 1/4″ thick for … Continue reading →

April 28, 2013 · Leave a comment

More pub chairs – day 1

Well the prototype pub chair seems to have been acceptable to the family so I have at least two more to build. Hopefully these two will go faster than the … Continue reading →

April 27, 2013 · Leave a comment

Pub chairs – day ten

Just a quick post today. I finished two more coats yesterday and one this evening. The pictures are all going to start looking the same at this point… I did … Continue reading →

April 22, 2013 · Leave a comment

Pub chairs – day nine

I had a chance to start finishing the chair last night so I applied the first coat of Tung oil. I decided to use tung oil because it a wipe-on … Continue reading →

April 21, 2013 · Leave a comment

Pub chairs – day eight

It occurred to me that the people from wood magazine may not have measured my kitchen counters when they put the plans for this chair into their magazine. I thought … Continue reading →

April 20, 2013 · Leave a comment

Pub chairs – day seven

I started out this evening by cutting the dados to receive the front stretchers. Since I don’t have a dado blade for the table saw, I decided to use my … Continue reading →

April 19, 2013 · 1 Comment

Number of visitors

  • 373,048 hits

Follow Blog via Email

Enter your email address to follow this blog and receive notifications of new posts by email.

Join 196 other subscribers

Browse by catagory

Browse my archive