Midnight Woodworking

Woodworking

Tag Archives: furniture

My Redesigned Roorkhee chair – day 6

Not much going on today. I am just putting the second, and probably final coat of polyurethane on the chair. I began by sanding everything down with a scotch-brite pad … Continue reading →

August 10, 2013 · Leave a comment

Pub chairs – day one

Started a new project today. This one is for my house so it will probably get pushed back to the back burner when other projects come along. I redid my … Continue reading →

April 12, 2013 · Leave a comment

Ironing board storage cabinet – day 10

I had a couple of hours to work last night so I drilled the last three pocket holes for the top. I glued it as well as screwing it down. … Continue reading →

April 5, 2013 · Leave a comment

Ironing board storage cabinet – day 9

I finally received my hardware to finish the cabinet. The first thing I did today was install the hinges. As I have discovered in the past, reading directions can often … Continue reading →

April 5, 2013 · Leave a comment

Ironing board storage cabinet – day 8

The glue has dried on yesterday’s patch job. I used my tiny plane to take down the edges of the plug then used my chisel to smooth down the top. … Continue reading →

March 31, 2013 · Leave a comment

Ironing board storage cabinet – day 7

I was thinking about the door hardware that I ordered for this cabinet. The hinges require a half inch deep bore for mounting. I wanted a raised panel look, to … Continue reading →

March 30, 2013 · 1 Comment

Ironing board storage cabinet – day 6

Made some progress today. It will probably take a week or so to get the hinges and drill bit that I ordered, so I decided to get everything else done … Continue reading →

March 29, 2013 · 2 Comments

Ironing board storage cabinet – day 5

The evening did not start well. Not working from a set of plans is really becoming a problem. I cut the top and the bottom so I could do a … Continue reading →

March 27, 2013 · Leave a comment

Ironing board storage cabinet – day 4

It has been a few days since I worked on this cabinet. I finally have the new table saw up and running so I could cut down the door panel … Continue reading →

March 26, 2013 · Leave a comment

Ironing board storage cabinet – day 3

Not doing much yet, the energy levels are better, but still down. I did get back to cleaning up the glue joints on my wider boards. I used the smoothing … Continue reading →

March 19, 2013 · Leave a comment

Ironing board storage cabinet – day 2

I didn’t get much accomplished today. My little shop helper has managed to pass his cold on to me, and my energy levels are much lower today. This morning, I … Continue reading →

March 16, 2013 · Leave a comment

Statue bases

While I let the benches cure in the shop I won’t be making any saw dust. I figured I would put up another project that I completed a few months … Continue reading →

March 7, 2013 · 3 Comments

Dining room bench build – day five

I learned something new today… Before I go into that though, I just want to mention that I do not learn well from books and classes. My best teacher has … Continue reading →

March 6, 2013 · Leave a comment

Sacristy cabinet delivery

I won’t have time to get into the shop today so I am posting the pictures of the sacristy cabinet that I delivered this past weekend. Since the cabinet was … Continue reading →

March 4, 2013 · 2 Comments

Dining room bench build – day two

I normally work from a plan on most of my projects, but these benches are pretty simple. I have built about a dozen of them. They consist of a bench … Continue reading →

March 2, 2013 · Leave a comment

Dining room bench build – day one

I have a couple of friends just down the road who asked me if I could build two benches for their dining room table. Since I don’t sleep much, and … Continue reading →

March 1, 2013 · Leave a comment

Eric’s new walnut chest

  Don’t let the red eyes fool you. He is a pretty good kid. A few years back, my oldest son decided that he was tired of his bedroom. He … Continue reading →

March 1, 2013 · 2 Comments

The Tenebrae Hearse

Tenebrae Hearse 3D pdf While I am waiting till I can deliver the sacristy cabinet, I figured I would post a few of the other projects that I have worked … Continue reading →

February 26, 2013 · Leave a comment

Day 16 – Sacristy cabinet

Finished up today. I had help so it all went faster… Before we could get started, Adam had to test the lock just to make sure that it worked ok. … Continue reading →

February 25, 2013 · 1 Comment

Day 15 – Sacristy cabinet

I started out the day by sanding down the first coat of polyurethane. The first coat is always rough. It raises the grain when it is first applied, and there … Continue reading →

February 24, 2013 · Leave a comment

Number of visitors

  • 373,257 hits

Follow Blog via Email

Enter your email address to follow this blog and receive notifications of new posts by email.

Join 196 other subscribers

Browse by catagory

Browse my archive