Saint Joseph’s asked me to build them a couple of cherry kneelers for their newly upgraded chapel. We looked at a lot of different styles of kneelers and I drew up some options. We settled on something light enough to be portable but sturdy enough that someone could lean on it to stand up. They also wanted the kneeler to fold up for a lower profile storage. I came up with some options then refined them a bit more. This is what we wound up with: KNEELER PLAN.pdf
Since I recently bought a new Onefinity CNC, I wanted to use this project to test it out so the first thing I did was cut several pieces of cherry into panels that I could use in the CNC.
Step one is to try to figure out work holding. I have some low profile clamps that work great but only if your board lines up with the tee-track…
I also needed to figure out dust collection. For the moment I only have one piece of equipment in the new building that I built for additional shop space, so I am starting with a shop vac and a dust separator. I got a DeWalt Stealthsonic vacuum and it is amazingly quiet, only 32 decibels.
And the dust separator is only 6 gallons but it works really well. Hardly any of the dust makes it to the vacuum and I can easily empty it without disconnecting everything.
The hard part was finding all the right size hoses but I managed. I also installed a boom arm to hold the hoses up, out of the way.
I used one of the extension tubes from the vacuum to extend above the spindle so nothing drags. Works great.
The dust boot is magnetically attached so that I can easily swap out bits in the spindle.
I installed a 1/4″ compression bit to make the first cut.
I left behind a few tabs to hold each piece in place when the cutting was done.
In surprisingly very little time, I had the first quatrefoil panel cut out. It only took about 5 minutes.
I set the program so that it would cut about 1/32″ deeper than the panel. It just barely cuts into the spoil board below. And I have my first parts.
I opened up the dust separator to see how much it collected. Almost no dust was left on the board. I think the dust collection system is a success so far.
I used a small razor saw to cut away the tabs and free the parts.
I quickly cleaned up the edges on my disc sander.
And all the curvy bits were cleaned up on the spindle sander.
I also added a cove to both sides of the curves on the router table.
They want some gold highlights so this will give me a location for that.
Next up I am cutting out the sides of the kneelers.
I was able to cut out both pieces from one panel and cut the dado for the shelf.
The big piece on the side is flipped around to become the bottom. This reorients the grain direction to make the bottom stronger and less likely to break along the grain line.
Next up is the sides of the pivoting kneeler. I cut the full outline as well as a pilot hole for the kneeler pivot. I will cut the correct size hole when I receive the hardware and can measure it.
In my other shop space, I started gluing up panel for the top.
Down in the shed, I test cut my first relief carving of a fleur de lis. I did a roughing pass with a 1/4″ bit that removes about 75% of the waste material, then did a finishing pass with a 1/16″ ball-nose bit.
When that was successful, I cut five more.
They turned out great and will require minimal sanding.
I need some form of joinery to attach the bottom part to the sides. I will be using my Domino jointer to make mortises so I marked a line on each side of the joint so I know where to cut.
I also started gluing up my quatrefoil panels. I am not sure the tiny ends will be big enough to hold together but I thought I would give it a try.
After laying out the Dominos, I use the jointer tool to cut the mortises.
I glued all of the tenons into one side.
Then add glue to the other.
Clamping these together, to dry, will be a challenge since there are no square edged to clamp against. I rooted through my scrap bin to find all of the off-cuts from the CNC.
I sued small pieces of sandpaper for friction pads between the scraps and the main body.
All of the off-cuts fit perfectly and the sandpaper held them in place well enough to get a good clamp-up.
Once I figured out the first one, I could mimic it on all the rest.
When everything was dry, I could start sanding the joints smooth.
I put a small round-over bit into the router table and eased the edges all the way around the sides.
I needed to plane down a board to make the shelf and front face. I have a digital gauge on my planer that is very accurate so I can make sure the board will be a tight fit in the dado.
I checked the board with calipers to make sure I have the thickness I need.
I compared this to the dados. My boards are .005″ thinner. That should be perfect allowing for the glue to swell the wood just a tiny bit.
I cut that board into the two shelf and two face pieces that I needed.
Then I can joint them and cut them to size.
The dry-fit worked perfectly.
I will need a small radius added to the corner after the panels are joined.
I glued the bottom and face boards together, making sure it was perfectly square.
Then I can cut my radius and dry-fit again.
The top panel that I glued up earlier was dry so that could be cut to size and have the edges rounded over. Then a good sanding of everything before assembly.
I need to add a stretcher to the bottom of the quatrefoil panel to attach to the sides.
This gets mortised for the Domino tenons as well.
Unfortunately not all of the quatrefoil panel stayed joined up. The end grain glue-ups tend to be weak. No problem, I can glue and pin the individual corners in place as needed.
Then I can glue and clamp the sides on.
A lot of creative clamping is required…
I don’t want to glue on the fleur de lis just yet because they will be gold leaf painted and the rest will be stained. Instead, I marked their locations and cut out masking on large sheets of blue painter’s tape on the laser.
These can be placeholders that will prevent stain from interfering with the glue later.
Now it is time to start painting things gold. I bought two different types of paint. an expensive liquid gold leaf paint and a less expensive gold acrylic. My thought is that the base coat can be the acrylic. It can fill any pores and be a backup in case the gold leaf gets scratched.
I am going to try a slightly different approach with the fleur de lis.
Since there are some open pores in the visible end grain, I am using a high-build primer to coat the wood first.
I will let those dry for additional painting later. Then, I sanded the quatrefoil surfaces to remove any overpainting prior to staining.
Since the top of the quatrefoil is end grain, I am not perfectly confident in the glue joint.
I decided to add a couple trim screws down from the top where the shelf meets the front face. Two on each side should suffice.
I marked and masked where the top will be glued on. Again to leave bare wood after staining.
I also decided to add a few screws to the sides of the front panel for strength.
I can make face grain plugs to fill the screw holes so that they will be barely visible.
These get glued and pressed into place then cut down with a flush-cut saw.
After a little sanding, you can barely even tell they are there.
Not bad.
Time to start staining.
All of the pieces are stained and left to dry over night.
And I can get back to the fleur de lis. I sanded the surfaces to prep for sanding. All of the open pores seem to now be filled.
Then I applied the first coat of acrylic paint.
The liquid leaf appears to be gold foil and other things in an alcohol based solvent. I shake thoroughly and start applying.
There is a noticeable difference from the glittery acrylic.
After they are painted, I start carefully applying the gold leaf paint to the quatrefoil, over the acrylic first coat.
After everything got yet another coat of liquid gold, I pulled off the masking from the kneelers.
I thinly spread wood glue across the back of the fleur de lis.
Then carefully locate them and hold them with a few tiny pin nails.
After they dried, I use spring clamps to locate the top.
Then peeled off the masking tape to apply glue to the masked area.
The clamps allow me to accurately replace the top so that I can screw the top into place.
The top also gets face grain plugs glued into place.
These have to be cut, sanded, and stained again.
Finally, my back-ordered kneeler hardware has arrived and I can start pre-installing some of it. I start by opening up the pivot point to the 17/32″ hole I need for the bushings.
I also installed the rubber feet on the bottom of the kneeler sides.
These were marked and pre-drilled.
Then screwed into place.
Having the hardware on the sides allows me to figure out the location of the pivot brackets.
After those are mounted, I can finally get a dimension for the cross support.
This gets screwed into place so that I can test everything.
That also allows me to create the kneeler pad now too.
After removing all of the hardware, I can stain the new parts then start applying polyurethane.
Polyurethane applied to the gold paint will offer additional protection to the gold.
After the first coat, everything gets sanded with 400 grit paper and wiped down for the second coat.
Everything is looking really good so far.
Time to figure out upholstery.
I have a sheet of 1″ thick high density foam padding. I used the kneeler pad to mark the size on the foam and cut six identical pieces.
Next I laid it on the fabric and cut about 5″ wider all the way around.
First step to attaching is to kneel on everything to fully compress it and place one staple in the center of each side.
This is intentionally too tight so that I can staple along the rest of the sides without the fabric pulling unevenly away.
After the sides are stapled, I can pull the original center staple, releasing the tension in the center and re-staple it at the relaxed location.
The ends were a bit more fiddley. I cut out a lot of excess in the corners and pulled the fabric in to staple it down.
Then I can screw the panels back onto the kneeler support bar.
Not perfect, but I think it looks pretty good, and the cushion doesn’t hit the face when they are up.
I like the way they look and they seem really stable.
This was a surprisingly challenging project but it was a really good first big project for my new CNC.