
The next project for Saint Peter’s church is a couple of new bases for the angle statues that are beside the altar. The older ones do not really match the existing back altar.
I plan on mimicking the columns on the front of the altar and just scaling them up to be large enough to support the angel statues on either side of the altar.
This is the design I came up with: statue col.pdf
These columns are too large to be made on my lathe in one piece so I will be making them in sections. The main body of the column will need a 6″ diameter blank to start so I cut up some 3″ thick red oak into pieces that I can use to make them. I have just enough to also make the columns for the next project as well so I cut them at the same time.
I need to plane one face flat and joint one edge square to the face. I do both of these operations on the jointer.
Then I cut each blank down to 6″ wide.
I applied wood glue to the planed face and spread it evenly across the entire surface.
I put a second block on top of that and clamped it tightly together.
These things are scary to put on the lathe and rough cut until they are round. It is a lot safer to cut the square blanks into octagons first so I laid out my 6″ circle to figure out the size of my octagon.
Then I set the table saw blade at 45° and cut off all of the corners.
I used a mallet to pound my drive center into place and set the large blank into the lathe.
I was able to safely spin it up to 1,800 rpms. That is way better than the 400 rpms I would have had to start at if it were square.
Now I can safely start cutting away the corners to create a round column.
I start by cutting the entire column to the widest dimension required on my columns, then once round, I can mark the locations of each feature.
If I hold my pencil on each mark while the blank is spinning, I can get a clear mark that I can see while cutting.
Then I can start roughing out all of the features.
Red oak is very porous and prone to tear-out. I lost a large chunk of one of my beads.
I found most of it so I glued it back on,
Then I cleaned up the notch that was left by cutting the sides square and flattening the bottom with a chisel.
I cut a small block that had the correct grain orientation and test fit it in the notch.
I glued that in place, slightly oversized so that I could cut it back.
After spinning the lathe back up, I was able to cut the bead back down to size. The patch fits nicely and the grain is a pretty good match.
Then I could get back to putting the curve on the bead. This part will eventually get painted gold so the slight color difference will not matter.
With the right side done, I could finish up the left.
Then I could proceed with cutting the middle section of the column down to the final dimension. I also cut the ends down to 1-1/4″ so that I have a feature to attach the wider part of the columns to later. Boy did that make a mess…
Time for sanding. I started with large strips of 60 grit sandpaper and worked my way all the way down to 220.
All sanded, the column looks really good. I swept up the mess after I cut down the second column and wound up with approximately 30 gallons of shredded oak shavings.
But I also had two finished column sections.
To create the tops and bottoms of the columns, I had to glue up several different sized panels.
Some were thinner than the 3″ thick boards so I had to resaw them down.
A majority of the resawing was done on the table saw, then it was finished up on the band saw.
The process leaves a thin bead on the cut face but that is easily removed on the planer as I brought them down to the correct thickness.
Then I got to edge glue all of the panels together to get the sizes I need.
Each end of the column gets an additional curved feature that would not fit on the center sections that I just turned. I laid out a rough diameter on each blank, marking the center for later use.
Then I can cut a rough circle on the bandsaw and screw on the face plate for the lathe. This faceplate was located over my center mark.
I attached the faceplate to the lathe and started roughing out my ends.
After I achieved the shape I wanted, I could drill a 1-1/4″ hole in the center for mounting onto the ends of the columns later.
After that, all I have to do is sand them from 60 grit down to 200 grit like the columns.
Now they should just press into place.
Makes a big difference in how the end of the column looks. I like it.
The top of the column gets a similar, but larger disc cut as well.
I repeated the same process that I used making the smaller ones.
These were dry-fit to both ends and they fit well.
To hold them on, I counter-sunk some pilot holes into the outer faces of the rounds then applied wood glue to the ends of the columns.
The ends were set in place and screwed on with some construction screws.
They are looking good. Now they get a heavy, square base and a thinner, octagonal top.
Since the base is thicker than the wood that I have, I make an additional layer for the square base that will join at the miter. I cut the miters for this board on the table saw.
Since these larger panels are too big for my planer, I tried to carefully glue them up to have a minimal seam that I could sand down on my drum sander.
The next step is to center the mitered plate on the bottom, then pre-drill and counter-sink.
I used some glue and screws to attach it as well.
The thicker base plate also gets a layer of glue, then the column gets clamped to it to dry.
While that dries, I can cut the top plate into an octagon on the miter saw.
I carefully centered the top plate on the column and clamped some temporary locating blocks into place so I could remove and replace after applying glue.
Then I applied some glue and used brad nails to hold the top on while the glue dries.
The brads are pretty subtle and they will be completely covered by the statues later.
When the glue was dry, I can give everything a thorough sanding and get it into the spray booth.
I still have to apply a coat of gold leaf paint to the beads but I wanted to get the first coat of polyurethane on first to fill some of the pores.
It was a bit of a journey to make these out of multiple parts but I think they turned out really nice.