Now that the front of the cabinets are done, it is time to think about the back. While the back of the panel is easily accessible, I want to create the frames that will hold the icons. I want them to be exactly centered on the arched openings so I used the CNC to cut out a template that was the width and height of the frames while cutting back a bit around the arch.
The arch on the template fits snugly into the openings, automatically centering the template.
With the locating template figured out, I can cut 3/4″ strips of cherry that match the exact length of the template.
I also cut short pieces that would go across the top and bottom as well.
I also want panels that will hold the pictures within the frames. These panels will be held in place with simple thumb screws. The thumbscrews will thread into these inserts.
To locate the inserts, I set up a jig on my drill press to locate each hole the exact same length from each end, then I drilled a hole to receive the insert. I can use a hex drive to set the inserts in place.
Once they are all installed, I can glue and attach the frame.
The glue will attach the frame permanently to the wood but a few brad nails will hold it in place while the glue dries.
Then I can just pop out my template and move it down to the next opening.
After a bit of work, all of my frames are in place.
I want the panels, that will hold the picture in place, to only be about 1/4″ thick. To create these, I need to resaw a thicker piece of cherry in half. If I am careful, I can get two panels from each board. First I joint the edges and make sure the board is the correct width, then pre-cut the length a little oversized to trim back later.
I can cut about the first 3″ of the resaw off each side, on the table saw. Then I can move to my bandsaw and finish cutting out the final 2″ or so in the middle.
The center section can be easily cleaned up on the planer. I can also plane them down to the final size as well.
Once the panels are the correct thickness, I can clamp them together and cut them to length.
Now I can return to my drill press and use the same setup to cut the larger hole in each corner of the panels. This will ensure that each panel is exactly the same and interchangeable with any other.
I can hold the panel flush to the bottom and side, and all of the holes line up perfectly with the threaded inserts behind.
My thumb screws haven’t arrived yet, but I can see that they are all lined up properly.
Time to start working on the rest of the cabinet.
The sides of the cabinet will be solid oak to match the wood on the front.
They need to be a little wider so I cut and milled pieces to be glue up into a wide enough board.
These were all clamped up and left to dry.
After an hour or two, I can pull the clamps and plane them down to the final 3/4″ thickness.
These were then cut down to their final size.
For the tops and bottoms, I am using 1/2″ oak plywood, mainly to reduce the weight a bit.
To create a rabbet for the plywood on the top and bottom to sit into, I installed my dado blade on the table saw and set up a sacrificial fence so that I could set the exact height and depth of the rabbet.
Then I ran the ends of the side panels along to fence to cut the rabbets.
This gives the plywood a recess to set in on the sides.
These can now get glued and clamped to the sides.
So the plywood has something to sit on along the front and back, I cut small strips that were beveled. These were glued and pinned into place using a plywood spacer to hold the depth from the top exactly where it needs to be.
While I was working on that, my thumbscrews arrived. I did a quick test fit to make sure the installed easily.
Then I got back to installing the plywood tops.
These were glued and pinned into place, then clamped while the glue dried. The same process was repeated for the bottoms.
While those dry, I can cut and mill all the wood for the rear face frames.
These will be attached using pocket holes. I set up my pocket hole jig and drilled two holes into the end of the narrow horizontal bars.
Glue gets applied to the end then the screws draw the horizontal bars up square and tightly to the sides.
When assembled, I sand all of the joints to make sure they are perfectly flush.
I made temporary vertical spacers to keep the plywood from bowing in as I installed the back frames.
These were also glued and clamped in place.
After they dried, I pulled the clamps and also installed all of my cherry covers for the icon panels just to make sure everything fit correctly.
The cabinets are nearly complete, I just need to make the rear door panels.